Skip to content

Damp, mold and leak detection

Damp and mold: find the source first

Damp and mold are a symptom, and the real treatment starts with the question of where the water is coming from: a leaking pipe, waterproofing on a balcony or roof, a window that has lost its seal, or condensation in a room without ventilation. Painting with anti-mold paint without dealing with the source brings the stain back, and opening a wall before a diagnosis can turn out to be unnecessary. So you diagnose first, then treat the source and dry out, and only at the end restore the finish. Agree in advance who carries out the diagnosis and what happens if the finding leads to the neighbors' apartment.

Typical range

150-15,000 ₪

by findings and scope of treatment

The range is a ballpark only. The final price is set after inspecting the property, the scope of work, the finishing materials and site conditions.

What's usually included?

  • Finding the source of damp
  • Testing and diagnosis
  • Repairing the source of the leak
  • Mold treatment
  • Restoring the finish

What affects the price?

  • Source of the damp
  • Extent of the damage
  • Access to the area
  • Need for testing
  • Coordinating waterproofing and repair

How does RBM help keep it organized?

  • Documenting findings and photos
  • Coordinating diagnosis and treatment
  • Check before restoring the finish
  • Sign-off with the client

Stages of the work

  1. 01

    Documenting the signs

    Before calling anyone in, photograph the stains, mark their edges in pencil and note when they get worse: after rain, after a shower or regardless. This information helps the diagnosis and prevents arguments later about what was already there.

  2. 02

    Diagnosing the source of the damp

    The professional uses a moisture meter, a thermal camera or a pressure test on the pipes, and presents a written finding with photos. At this stage you find out whether the source is in the home, on the balcony, in the roof or at a neighbor's, and decide who is responsible for what comes next.

  3. 03

    Treating the source

    Whatever is causing the damp is dealt with: replacing a section of pipe, re-waterproofing a balcony, renewing the seal around a window or improving ventilation. The homeowner approves the extent of the opening-up in advance, so no more flooring or wall is removed than needed.

  4. 04

    Drying and monitoring

    After the repair the wall needs to dry, sometimes with dehumidifiers and repeated moisture readings. Here you agree which moisture meter reading counts as dry enough, and who confirms it is OK to move on to the finish.

  5. 05

    Mold treatment

    The affected areas are cleaned and disinfected, loose plaster is scraped off, and materials that absorbed water and cannot be dried are removed. Agree how the furniture and clothes in the room are protected, and when it is OK to sleep there again.

  6. 06

    Restoring the finish

    Only once the wall is dry are plaster, filler and paint suited to damp rooms applied, with the color matched to the rest of the wall. The final payment is made after the homeowner has seen that the stain does not return under the conditions in which it appeared.

What to check before you pay

  • Ask for a written finding with photos showing what was found to be the source of the damp, before approving opening up a wall or flooring.
  • Make sure the moisture reading is repeated after drying and the result is documented, before anyone starts plaster or paint.
  • Check the repaired area after the next rain or after normal use of the shower, and compare it with the original photos.
  • Make sure all materials that absorbed water, such as loose plaster or soft drywall, were removed and not just repainted.
  • Ask to see the replaced pipe sections or the new waterproofing before they are closed up behind a wall or flooring.

Damp, mold and leak detection price list by line item

6 line items · updated 11/2026

  • Leak detection (thermal camera / pressure test)

    900-2,200 ₪

    per test · Inspection and diagnosis only, no repair. Findings report depends on the provider.

  • Spot mold treatment

    500-2,500 ₪

    per area · Cleaning, disinfecting and local treatment; depends on the size of the area and the source of the damp.

  • Scraping, plaster and anti-mold paint

    150-350 ₪

    per m² · After treating the source of the damp; includes dedicated materials.

  • Fixing damp from a balcony or roof

    3,000-15,000 ₪

    per repair · Depends on the source, access, lifting tiles and re-waterproofing; details in the waterproofing category.

  • Drying walls after flooding

    1,500-6,000 ₪

    per project · Dehumidifiers, moisture meters and monitoring; drying time depends on how severe the damp is.

  • Resealing around a window

    400-1,200 ₪

    per window · Removing old silicone, cleaning and resealing, including minor finishing repairs.

Updated November 2026 · price varies by spec and site conditions

See the full price list

Questions about Damp, mold and leak detection

Why is it important to find the source of the damp?

Because paint, plaster or anti-mold products do not stop water. If the source keeps leaking, the stain comes back and the new finish is ruined, and sometimes the damage spreads inside the wall without being seen. A proper diagnosis also defines the scope of work: sometimes renewing the seal around a window is enough, and sometimes the balcony flooring has to be opened up. A familiar example is a stain on the bathroom ceiling that is painted over again and again, until it turns out the source is damaged waterproofing in the shower floor of the apartment above, and that meanwhile the damage has spread into the ceiling.

Are special tests always needed?

Not always. When the source is clear, such as a visible leak under the sink or a condensation stain in the corner of a room without ventilation, you can start with the repair. When the stain appears for no clear reason or comes back after an earlier repair that did not help, testing with instruments helps find the source before walls are opened based on a guess. When you order a test, ask in advance what the report includes, whether it states the source and the recommended treatment, and whether the person testing also offers to carry out the repair.

What do you do when the damp is coming from the neighbors' apartment or the shared roof?

Document the damage and the diagnosis finding, and contact the neighbors or the building committee with the photos and the report. Do not restore the finish on your side before the source has been dealt with, otherwise the work will be ruined again. When there is a dispute about the source or the responsibility, consult a qualified professional who can prepare an expert opinion. Also ask the neighbors to allow a test in their apartment, for example a flood test of the shower or a pressure test on the pipes, because without it it is hard to show where the water is coming from and who needs to deal with it.

Can you sleep in a room with mold during the treatment?

Better not during the cleaning and scraping, because spores and dust spread through the air. Close the room, take out clothes and textiles and ventilate well after the work. If there is a baby, an older person or someone with respiratory sensitivity in the home, it is worth asking a doctor about returning to the room. Also agree with the contractor how the removed materials are taken out, in sealed bags and without passing through the whole home, and how the dust is cleaned up after the work, so the spores do not move to other rooms.

How do you compare quotes for treating damp?

Check whether the quote starts with a diagnosis or jumps straight to anti-mold paint. A good quote separates the diagnosis, treating the source, drying and restoring the finish, and says what happens if the finding differs from the estimate. Be wary of a quote that promises a solution without anyone having checked where the water is coming from. Also ask whether the price includes drying and a repeat measurement or whether they cost extra, what happens if the stain returns in the same place after treatment, and whether the contractor comes back to check at no extra charge.

How do you stop the mold from coming back?

Once the source has been dealt with, most of the work is ventilation: opening a window or running a fan after showering and cooking, and not pushing cabinets against cold exterior walls. Check the silicone around the windows and the bathtub from time to time and renew it when it cracks. Keep the diagnosis report and the repair photos for future treatment. In a room where mold came back in the past, put a simple humidity meter in place and check it from time to time, because a rising reading warns you before the stain shows on the wall or you notice a musty smell.

Related renovation work

Registered renovation contractors by city

Search for a contractor by name or contractor number

Looking for a contractor for damp, mold and leak detection?

Build a project file with a cost range, milestones and terms, and send it to contractors who work in an organized way.

Build a project file

We use cookies to improve your experience.