Skip to content

Plaster and skim coat

Plaster and skim coat: the stage that decides how the paint will look

Plaster and skim coat are work you don't see at the end, but every flaw in them is exposed after painting under side lighting. Plaster builds up the wall and straightens it, and skim coat smooths it for the finish, so it's important to know in advance which layer each wall needs. The common mistakes are plastering a wet or crumbling wall, drying too fast, and a thick skim coat hiding a crooked wall. Before getting quotes, check the condition of the walls together, mark the cracks and ask whether the source of the problem has been dealt with.

Typical range

75-650 ₪

per m², by finish type

The range is a ballpark only. The final price is set after inspecting the property, the scope of work, the finishing materials and site conditions.

What's usually included?

  • Surface preparation and cleaning
  • Base plaster and leveling
  • Skim coat and smoothing
  • Repairing cracks and defects
  • Sanding and preparing for paint

What affects the price?

  • Condition of the existing walls
  • Number of coats required
  • Area to be smoothed
  • Type of plaster and materials
  • Access and working height

How does RBM help keep it organized?

  • Checking the condition of the walls
  • Coordinating the application method
  • Checking the surface before painting
  • Approving the finish by area

Stages of the work

  1. 01

    Checking and marking the walls

    By tapping and using a straightedge, find where the old plaster is hollow, crumbling or crooked, and mark cracks and damp stains. At this stage you decide which walls get new plaster, which get only skim coat, and what level of finish is required.

  2. 02

    Removal and substrate preparation

    Loose plaster is removed, dust and grease are cleaned off, and the wall is dampened or a bonding coat is applied, depending on the type of wall. The homeowner approves the actual extent of removal, because sometimes it turns out there is more loose plaster than was visible during the walkthrough.

  3. 03

    Plastering and straightening

    Corner beads and guide strips are installed and plaster is applied in coats until the wall is straight under a straightedge. Before moving on, check the corners and the straightness of the long walls together with the contractor, and approve the stage.

  4. 04

    Drying and closing cracks

    The plaster is left to dry slowly, without direct heating and without strong wind, and cracks are closed with mesh and a flexible compound. At this stage you decide together whether a particular crack calls for consulting an engineer before it is covered.

  5. 05

    Skim coat and sanding

    Skim coat is spread in thin coats, sanded between coats and finished with fine sanding. Before painting, the homeowner goes over the walls with a flashlight held close to the surface and marks spots that need more smoothing or sanding.

  6. 06

    Cleaning and handover for painting

    Sanding dust is cleaned off the walls and floor and a primer coat is applied, so the painter gets a ready surface. The handover is done by area, and the homeowner confirms in writing that the walls are ready before paying for the stage.

What to check before you pay

  • Check every wall with a long straightedge and side lighting, and look for dips, waves and corners that aren't straight before you pay for the plastering.
  • Tap gently on the new walls and check that there's no hollow sound, which would indicate plaster that didn't bond to the wall.
  • Make sure the cracks marked during the walkthrough were closed with mesh, and ask for a photo of each crack before it is covered.
  • Check that wall corners and window and door frames are straight and clean, with no skim coat left on the frames or on the outlets.
  • Ask to see the wall with a flashlight held close after sanding, before the painter starts and before you pay for the stage.

Plaster and skim coat price list by line item

7 line items · updated 11/2026

  • Interior plaster, by hand

    120-220 ₪

    per m² · For interior walls; depends on the thickness and leveling needed.

  • Interior plaster, machine-applied

    90-160 ₪

    per m² · Suitable for relatively large areas.

  • Exterior plaster

    160-360 ₪

    per m² · Affected by scaffolding, access and finish coats.

  • Skim coat (American filler)

    75-130 ₪

    per m² · Leveling and smoothing before painting, usually including material.

  • Crack repairs

    250-1,500 ₪

    per area · Depends on whether it's a cosmetic repair or a structural problem.

  • Closing a door opening

    1,200-3,500 ₪

    per opening · Includes blockwork, plaster and basic finishing repairs.

  • Decorative plaster

    200-650 ₪

    per m² · Venetian plaster, colored render or special finishes.

Updated November 2026 · price varies by spec and site conditions

See the full price list

Questions about Plaster and skim coat

What is the difference between plaster and skim coat?

Plaster is a relatively thick layer that builds up the wall, straightens it and covers blocks or large defects. Skim coat is a thin layer that smooths the wall surface before painting. A new or damaged wall usually needs both plaster and skim coat, while a wall in good condition sometimes needs only skim coat. Ask for the quote to state which layer each wall gets. For example, a new block wall gets full plastering, while an old wall in good condition sometimes needs only repairs and skim coat before painting, and the price differs accordingly.

Why does the preparation stage affect the final price?

A wall in poor condition requires removing loose plaster, more coats, more material and more drying time. If the preparation isn't done properly, the defects show up only after painting, and then the fix includes repainting too. So the quote should spell out what preparation includes and how removal that turns out larger than expected is priced. For example, in an old apartment it sometimes turns out that much of the plaster on a wall is hollow and has to be removed down to the blocks. Agree in advance how that kind of removal is measured and priced. Ask to see the wall before deciding.

What do you do with a crack that comes back after every paint job?

A crack that keeps coming back usually indicates movement in the wall, a joint between different materials, or moisture, and ordinary skim coat won't hold it. It is treated with mesh and a flexible compound, and for wide or diagonal cracks, or ones that keep growing, consult an engineer before covering them. Photograph the crack with its ends marked, so you can see whether it keeps growing. For example, a long horizontal crack above a window or a crack at the joint between a wall and the ceiling behaves differently from a small hairline crack in the plaster.

Can you live at home during plastering and skim coat work?

You can, but be prepared for dust. Sanding the skim coat produces very fine dust that spreads throughout the home, so seal openings with plastic sheeting and ask for an industrial vacuum to be used during the work. While it dries, good ventilation is needed, without an air conditioner or heater aimed straight at the wall. Cover furniture and clothes even in rooms where no work is being done. For example, skim coat dust that gets into the kitchen settles on countertops and inside drawers, so empty or seal open cabinets before sanding. Also turn off the air conditioner during sanding.

How do you compare plaster and skim coat quotes?

Ask for each quote to spell out which walls get plaster, which get skim coat and what level of smoothing, not just a total area. Also check what's included in removing old plaster, closing cracks, corners and cleanup. A quote that doesn't distinguish between plaster and skim coat is hard to compare and hard to check at the end. Also ask whether the primer coat for the paint is included in the quote or left to the painter. For example, a quote with an overall price per m² and no breakdown may include only skim coat, while your walls need full plastering. Ask for a breakdown for each wall separately.

When can you paint after new plaster?

Only after the plaster is completely dry, and that depends on its thickness, the weather and ventilation. Paint on damp plaster can peel or leave stains. The contractor should say when he thinks the wall is ready and check it, and that decision should be written down before the painter arrives. Good ventilation without direct wind helps the wall dry evenly. For example, dark stains that appear on the wall after painting often show that the plaster hadn't dried yet. Ask the contractor to check the wall at its thickest spots before you approve painting.

Related renovation work

Registered renovation contractors by city

Search for a contractor by name or contractor number

Looking for a contractor for plaster and skim coat?

Build a project file with a cost range, milestones and terms, and send it to contractors who work in an organized way.

Build a project file

We use cookies to improve your experience.